ATSS LARGE HOOTER
Siren/Hooter connect to the control panel to raise an alarm to threaten the intruder run away.
The External Siren installed and wired to the Control Panel will activate in the event of an intrusion with the system armed. In the event of the cable to the Siren Unit being deliberately cut an alarm will be generated at the control panel, provided that the tamper circuit to the Siren has been connected.
Siren should be located as high as possible in a prominent position so that it can be easily seen and heard. When running the cable to the siren, the cable should pass through a hole in the external wall and enter through the rear of the casing.
Sounds generated by the system can be made different for various system alarms. In addition, the type of sound can help to scare away an intruder or evacuate the building during a fire.
During a burglary the siren’s sound is startling, but more effectively, filling the room with sound blocks the intruder’s ability to hear police sirens approaching. This lack of ability to hear into the distance raises the panic level of an intruder most likely making them want to leave. Consider outfitting the system with indoor sounders to fill the room with noise and outdoor sirens to call for the immediate attention of neighbours.
- Description
- Additional information
- Global Tab
Description
Siren/Hooter connect to the control panel to raise an alarm to threaten the intruder run away.
The External Siren installed and wired to the Control Panel will activate in the event of an intrusion with the system armed. In the event of the cable to the Siren Unit being deliberately cut an alarm will be generated at the control panel, provided that the tamper circuit to the Siren has been connected.
Siren should be located as high as possible in a prominent position so that it can be easily seen and heard. When running the cable to the siren, the cable should pass through a hole in the external wall and enter through the rear of the casing.
Sounds generated by the system can be made different for various system alarms. In addition, the type of sound can help to scare away an intruder or evacuate the building during a fire.
During a burglary the siren’s sound is startling, but more effectively, filling the room with sound blocks the intruder’s ability to hear police sirens approaching. This lack of ability to hear into the distance raises the panic level of an intruder most likely making them want to leave. Consider outfitting the system with indoor sounders to fill the room with noise and outdoor sirens to call for the immediate attention of neighbours.
Additional information
| Weight | 0.23 kg |
|---|---|
| Dimensions | 12 × 22 × 123 cm |
Pellentesque habitant morbi tristique senectus et netus et malesuada fames ac turpis egestas. Vestibulum tortor quam, feugiat vitae, ultricies eget, tempor sit amet, ante. Donec eu libero sit amet quam egestas semper. Aenean ultricies mi vitae est. Mauris placerat eleifend leo.
Donec sed tincidunt lacus. Duis vehicula aliquam vestibulum. Aenean at mollis mi. Cras ac urna sed nisi auctor venenatis ut id sapien. Vivamus commodo lacus lorem, a tristique sapien tempus non. Donec fringilla cursus porttitor. Morbi quis massa id mi pellentesque placerat. Nam scelerisque sit amet diam id blandit. Nullam ultrices ligula at ligula tincidunt, sit amet aliquet mi pellentesque. Aenean eget fermentum risus. Aenean eu ultricies nulla, id bibendum libero. Vestibulum dui augue, malesuada nec tellus vel, egestas condimentum ipsum. Vestibulum ut.
Related Products
-
2 Fingerprint Reader Connectivity
-
VIBRATION SENSOR-ATSS
Most of the sensors detect opening of a door, window or breakage of glass or movement of human beings. But it is equally important to detect if there is a break-in attempted through walls, ceiling or floors. This can be detected with the help of vibration Detectors.
The detector operates on the principle of resonance of frequency. When the external impulse frequency due to hammering or chiseling matches with the resonance frequency of the sensing element, the alarm is triggered off. False alarms are avoided with proper setting of the intensity controller. The vibration detector can be fitted to windows, door frames, walls, ceilings etc.
A typical vibration detector is effective up to 2.5 meters depending upon its location and the material to which it is fixed. Each detector can set to its own optimum level of sensitivity. There should be a sensor for every 20 ft of wall accessible to the intruder. Sensitivity should be adjusted to suit local vibration requirement.
-
Network Video Recorder
-
ATSS PIR MOTION SENSOR
Passive Infrared (PIR) Motion Sensors protect space by ‘looking’ for changes in infrared (heat) energy levels caused by movement of an intruder.
The passive infrared detectors are passive devices. i.e., they do not transmit any form of energy. When a person enters and moves within the detecting zone, his body which is at its normal temperature of 98.6 degree F., radiates more (or less) thermal energy than the surroundings and such minute difference in thermal energy is detected by the PIR.
In simple words, PIR keeps a picture of t
-
ATSS RECESSED MOUNT SWITCH
Recessed has the magnet placed in a 3/8″ hole drilled into the edge of the door,and the switch in another hole drilled into the door casing, wiring concealed in the wall.
Recessed Magnetic Door Sensors are typically used on closed circuit alarm systems. These devices work by magnets. These magnet sensors are mounted inside of the door and inside of the frame. When the door is closed and the magnets are lined up, the switch is closed. These devices are made to be ascetically pleasing, since they cannot been seen and also to be less prone to tampering. Below are the pros and the cons of using this type of door contact.
Pros of Recessed Magnetic Door Contacts
Less Risk of Tampering: since these devices are installed inside the door and frame they are far less likely to be tampered with since they cannot be seen when the door is closed. Invisible when door is closed: This makes for the devices to be more aesthetically pleasing than the surface mounted door contacts. These are the standard type of contacts used in residential settings for this reason.
Cons of Recessed magnetic Door Contacts
Harder to Install than surface contacts: Since they have to be installed the door and the frame, they are more difficult to install than the surface contacts which stick right onto the outside.
Alternatives
The other alternative to using recessed door contacts is to used surface door contacts. These are typically a little cheaper and easier to install than the recessed door contacts, but they are visible and more prone to tampering.
-
BOUNDARY DETECTOR-ATSS
Boundary Detector that covers a building’s perimeter,Boundary Detector long, narrow detection area comes from the center point, covering both sides. Boundary Detector creates a multi-layered,horizontal barrier that detects intruders and sounds the alarm before they actually break in.Just one boundary detector can protect a long area,because it is installed in the center of the detection area and protects on both sides. makes you feel secure in knowing your building is well guarded.
-
ATSS SURFACE MOUNT SWITCH
The surface mount is as its name implies, mounted on the surface of the door/window with wiring exposed. A door contact is the most basic of alarm triggers.
These are just magnetic strips that are in contact while the door is closed but break the circuit when the door is opened. Then it triggers the alarm.
Surface Mount Magnetic Sensor are used on closed circuit alarm systems. These devices work through a magnets, so when the magnets are lines up, the switch is closed. These types of devices are meant to be an easy to install option for windows and doors that open. Below are the pros and cons of these devices and alternatives to using them.
Pros of Surface Mount Magnetic Door Contacts
Ease of installation: These devices are typically mounted through an adhesive that sticks to the door and the frame. They can also be mounted with wood or sheet screws depending upon your door or window you plan on installing it on.
Cheap: These devices are normally very cheap, the biggest cost with them is the installation and wiring if they are used on hardwired alarm systems.
Reliable wireless devices an option: There are reliable wireless surface mounts that are more expensive than the hardwired ones, but can allow you to quickly install them without running wires and paying someone house of installation fees.
Cons of Surface Mount Magnetic Door Contacts
Visible: They are not aesthetically pleasing to the eye in residential settings.
Subject to tampering: Since they are visible, it makes the more subject to tampering with. It can also alert burglars of the type of contact sensors you use and they may be able to find a window or door without them since they know they are not mounted inside of the door or windows.
Alternatives
Since the biggest downfalls of these devices are that they are not aesthetically pleasing and are subject to tampering there is a device called a recessed contact. This device woks pretty much the same way as the surface contact but the magnets are installed inside the frame and the door.
-
GLASS BREAK DETECTOR-ATSS
A glass break detector is a sensor used in electronic burglar alarms that detects if a pane of glass is shattered or broken.These sensors are commonly used near glass doors or glass store-front windows to detect if an intruder broke the glass and entered.
Glass break detectors usually use a microphone, which monitors any noise or vibrations coming from the glass. If the vibrations exceed a certain threshold (that is sometimes user selectable) they are analyzed by detector circuitry.
Simpler detectors simply use narrowband microphones tuned to frequencies typical of glass shattering, and react to sound above certain threshold, whereas more complex designs compare the sound analysis to one or more glass-break profiles using signal transforms similar to discrete cosine transform (DCT) and fast Fourier transform (FFT) and react if both the amplitude threshold and statistically expressed similarity threshold are breached.
-
ATSS OVERHEAD MOUNTED SWITCH
Roller shutter contacts are very similar to door contacts and work in exactly the same way. The difference is that roller shutter contacts are more heavy duty.
-
Fingerprint Time & Attendance Recorder
